هیچ محصولی وجود ندارد
این محصول در انبار موجود نیست
اخطار: آخرین موجودی فعلی!
تاریخ در دسترس بودن
By buying this product you can collect up to 1400000 loyalty points. Your cart will total 1400000 loyalty points that can be converted into a voucher of 280,000 تومان.
چرخ فیلتر QHY مدل CFW3M-US و CFW3M-SR
دریافت کننده :
* فیلدهای مورد نیاز
1. Do not insert your fingers into the round holes on the filter wheel, otherwise the filter disc may cause finger injury.
2. The copper nails in the filter wheel cannot be disassembled, otherwise the filter wheel will loosen and affect normal use.
3. When the camera uses the control line to control the filter wheel, it is forbidden to use the USB cable to connect the filter wheel at the same time to prevent the power supply from damaging the filter wheel.
4. For the frameless filter, when using the screw to press the lens, it must be pressed by the plastic gasket, but not directly with the metal nut of the screw. Otherwise there is a risk of crushing the lens.
1. Control port switching button: This button is used to set the interface mode. There is two mode: USB control mode and 4PIN conrol mode. If you use the USB cable to control QHYCFW3 you need to select the USB control mode. If you use the 4pin QHYCFW socket cable to control the QHYCFW3 from QHYCCD camera, you need to select the 4PIN control mode. This switch button is inside the case. You can push it on and off. But since it is inside the case, you can not know which position it is. So QHYCFW3 has a LED indicator to tell you of it. When the filter wheel is powered on , if the indicator light flashing for one second and it is red color, the filter wheel is in the USB control mode; if green color the filter wheel is in the 4PIN control mode.
2. Status indicator: Each filter wheel hole position corresponds to a specific color. And this indicator will display if the CFW3 working in the USB control mode or the 4pin control mode. When power on the QHYCFW3, it will be on for one second then off. If it is red color, the QHYCFW3 is in USB control mode. If it is green, the QHYCFW3 is in 4pin mode. the indicator light is off to prevent shooting light pollution the indicator light is off to prevent shooting light pollution.
3. Reset button: After pressing, the filter wheel hardware is reset, the turntable returns to the initial position, the default hole 1
Filter wheel standard accessories
1. Filter wheel body
2. 2-inch extension tube
3. M4 metal hand screws
4. Filter fixing nails, including gasket
5. Filter wheel connected to camera control line
After connecting the camera, go back to the interface and select Setup Filter to select the filter wheel. Follow the steps (as shown).
Select the appropriate hole position to operate.
Use the USB cable to plug into the USB port of the filter wheel and the other end to connect to the computer.
Open the device manager to check the port number (if the driver is installed on the computer, the driver to be installed will be detected automatically, otherwise the 2CP210X driver will need to be installed).
Open the MaxIm DL software and click on Camera Contorl. As shown
After confirming the error, click the ok button continuously. Go back to the Camera Control page.
Note 1: When send a goto command to QHYCFW3. Motor will start goto the target position. After arrived. QHYCFW3 will send back the current position.
For example: Now QHYCFW3 is in position 1(position1=command 0) and tar(et is position 4(position4=command 3). After the color wheel arrived the target , it will send back
But if current position is 1 (position1=command 0) and you send the same position (command 0) to QHYCFW3 . Color wheel will not rotate. And in the old version (the version before 201409) the color wheel will not send back any info in this condition. In the new version . the color wheel will send the current position:
This modification is used to judge if the colorwheel has arrived the target for the host software.
Note 2: There is no this function before Version 201409. If you call this function QHYCFW2 will reply nothing.
Note 3:Tere is no this function before Version 201409. If you call this function QHYCFW2 will reply nothing.
Note 4:Tere is no this function before Version 201409. If you call this function QHYCFW2 will reply nothing.
VRS MXP NOW RESET
No customer reviews for the moment.